Iii Body Armor

AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating


AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating
AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating
AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating
AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating
AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating

AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating    AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating

Tactical Scorpion Gear AR500 steel plate body armor. A stand alone armor plate with multiple hit capability. Fully Frag Spall build-up coating on strike faces. Fully tested by independent Lab (documentation sent by request). Rated for up to six hits from 7.62 Nato bullets.

308 Winchester with velocities up to 2780 fps. For front and/or back protection. Plate Size: 10" x 12" - Two curved plates. There are many online videos documenting the strength and reliability of our armor plates as our plates can take far more punishment than they are rated for and when your well-being is at risk, you should not take chances with lesser quality body armor. Our build-up spall coating is done with a Graco EXP-2 which is the top of the line high pressure heated coating system. Our AR500 plate is chemically washed and etched on the strike surface to eliminate the coating from delaminating when shot which keeps the shrapnel from escaping from the armored assembly. We utilize a CNC laser cutting table for the cutting of all our AR500 products. There is no equal method. Lasma cutting cuts slowly, this puts a lot of heat into the steel.

(Submerged plasma cutting machine is no better) This excess heat can result in excessive chipping and damage near the cut edge during use and easily shattering when shot. Plasma cutting generates large amounts of heat that is deposited into the steel, softening it's edges.

Plasma cutting is the largest out of the most commonly used methods for cutting abrasion resistant steel. Most AR500 is cut with plasma cutters as they are cheap and relatively small compared to laser cutting. Our Curved plate is bent on a laser cut custom die set with single radius bend which provides a perfect radius on each and every plate we produce, not bent multiple times on a press brake which provides uncontrollable results.

Here at Tactical Scorpion Gear we manufacture our own vest carriers, Kevlar level IIIA vests and all our products. Weights : All weights are in pounds.

6x6: 3 6x8: 3.4 10x12: 8 11x14: 10.3. 6 x6 : 3.4 6x8: 3.8 8x10: 10x12: 8.4 11x14: 10.7. Will withstand multiple hits from all pistol calibers. Tested by HP White laboratory.

This model complies with NIJ Standard-0101.06 for Ballistic Resistance of Body Armor. NIJ tested Level III Armor will defeat 6 rifles round shots up to 7.62x51/. Purchaser is encouraged to seek qualified legal counsel in his/her jurisdiction if Purchaser has any questions concerning ab federal, state, or local laws. Body armor will not protect someone from injury or death in all circumstances.

Body armor will not provide any protection for the parts not covered by the armor. Purchaser acknowledges that there is always a risk of injury, including serious injury or death, if struck by a bullet while wearing body armor.

ALL WARRANTIES, INCLUDING THE WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY, ARE HEREBY EXCLUDED. These Terms and Conditions may be updated, revised, or changed without prior notice. We stand behind everything we sell. Guarantee doesn't cover ordinary wear and tear or damage caused by improper use or accidents.
AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating    AR500 Steel Body Armor Level III Pair 10 x 12 Plates Frag Coating